Only a few units in stock
-40 %
Stock: In Stock
Model: Mega 2560 R3 (Compatible) 16u2
Mega 2560 R3 (Compatible) 16u2This is a clone of quality, not only just aesthetically , also uses the same chip USB connection so it is 100 % compatible with the original drivers.It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ..
24.99€ 14.95€
Ex Tax:12.36€
Out of Stock
Stock: Out of Stock
Model: Servo-SG90
This small servo is commonly used in 3d printers to move small parts that do not need much force as arms for position sensors.- Dimensions approx: 22x11.5x27 mm- Movement speed: 0.12 sec / 60 deg at 4.8 v no load- Torque: 1.2 kg / cm to 4.8 v- Operating voltage: from 3v to 7.2v- Includes 3 arms and ..
2.75€
Ex Tax:2.27€
Only a few units in stock
-36 %
Stock: In Stock
Model: Mini-12864-LCD
Actual Version: 2.1Mini 12864 LCD for an independent printing.Small LCD, but with all the information and features of the popular 12864 LCD, it's easier to install in small 3D printers or where you're looking for a discreet finish.This Full Graphic Smart Controller contains a SD-Card reader, an
rot..
24.99€ 15.99€
Ex Tax:13.21€
-9 %
Discontinued
Stock: Discontinued
Model: MK2A-300x200
MK2b Heated Bed 300x200mm
The hot bed is responsible for heating the bottom of the 3D
printer, so that the pieces remain adhered during printing. Thus the
warping (parts bulge and come off during printing process) is
avoided.
More information:
http://reprap.org/wiki/PCB_Heat..
32.99€ 29.99€
Ex Tax:24.79€
-62 %
Stock: In Stock
Model: MK2B
The hot bed is responsible for heating the bottom of the 3D
printer, so that the pieces remain adhered during printing.Thus the
warping (parts bulge and come off during printing process) is
avoided.
More information:http://reprap.org/wiki/PCB_Heatbed
..
17.99€ 6.80€
Ex Tax:5.62€
-19 %
Out of Stock
Stock: Out of Stock
Model: MK3-avellanada-conexion
Features similar to MK2, for 12 volts:Hot bed with 3 mm aluminum coreThe metal part is the upper print side and the black side is the lower side. It is recommended to insulate the bottom side with thermal insulationFor 12 volt sourceWith countersunk holes for screw head and With ready connectionThe ..
15.99€ 12.99€
Ex Tax:10.74€
Only a few units in stock
-23 %
Stock: In Stock
Model: Mk3-22+cristalmicroporoso
MK3 aluminum and glass with microporous coating.The heated bed is an evolution of the conventional 3mm MK3 hot bed, being more powerful and lightweight, it has been designed to be used with the microposoro coating.It has similar characteristics to MK2, for 12 volts:Heated bed with 1.5 mm aluminum co..
49.00€ 37.90€
Ex Tax:31.32€
Only a few units in stock
-33 %
Stock: In Stock
Model: MK52
CharacteristicsRated voltage: 24vIncludes strong neodymium magnets that do not lose properties up to 140ºC9 fixing holes for countersunk screwsPre-welded power cablesThermistor included with connectorNominal power 180w for fast and uniform heatingIt may present some superficial scratches as it has b..
89.00€ 59.95€
Ex Tax:49.55€
-67 %
Out of Stock
Stock: Out of Stock
Model: dual-axis-module
Simple complement to connect two motors in parallel, usually used with Z axis, but can be used with any other axis. Recommended to connect two equal motors so that the current is distributed equally between them.Use with small or medium sized 3D printers, avoid large sized motors.Content:1x Boa..
2.99€ 0.99€
Ex Tax:0.82€
-40 %
Stock: In Stock
Model: mosfet-module
It can control the current of devices or accessories, such as fans, or additional lights.Signal Voltage: 3.3V, 5VOutput voltage: 0-24 VRated current: <5A (To overcome 1A it needs additional dissipation)Size: 33 x 25mm
1 Piece
..
2.99€ 1.79€
Ex Tax:1.48€
Only a few units in stock
-40 %
Stock: In Stock
Model: 17hs2408
Features: Each motor includes 1 meter of wire with dupont connector at its end. The shaft motor is D type, which eases the use of pulleys or couplers. Nominal electrical specifications:ModelStep Angle (deg)Motor Length (mm)Rated Current (A)Phase resistence (ohm)Phase inductance ..
12.50€ 7.50€
Ex Tax:6.20€
-40 %
Stock: In Stock
Model: 17hs3401
Features:17HS3401: Compact Size, ideal for applications where you need lightweight, as mobile extruders, or other cases that works with low loads as CNC lasers, plotters and others. Each motor includes 1 meter of wire with dupont connector at its end. The shaft motor is D type, which eases..
13.00€ 7.75€
Ex Tax:6.41€