-20 %
Stock: In Stock
Model: Cristal-recubrimiento-310x310
This printing base is a glass with microporous coating that increases adherence. Also, you do not need clamps for placement.Features:Great adhesion: it is covered by microporous coating, which has an adhesion during printing. Once it cools, it's easy to take off.Superplanitud of surface, f..
45.00€ 35.80€
Ex Tax:29.59€
Hot Sales
-74 %
Stock: In Stock
Model: DRV8825
The DRV8828 is a driver for stepper motors, with a resolution of 1/32 steps. Datasheet: https://www.pololu.com/product/2133 Heatsink included with thermal tape1 Piece ..
8.99€ 2.33€
Ex Tax:1.93€
Only a few units in stock
-54 %
Stock: In Stock
Model: Filament-Sensor-1.75
Mechanical filament presence sensor, with a simple and effective design.Compatible with 5V and 3.3V.Includes 1m cable approx.Warning: It is important to see the connection diagram and connect it correctly, if it is connected incorrectly, the electronics can be damaged.1 unit..
7.26€ 3.35€
Ex Tax:2.77€
New
-13 %
Stock: In Stock
Model: FYSETC-Cheetah-Board
Current Version: V1.2bDesigned for a single extruder 3D printer. Many interfaces are reserved for features such as AC detection, filament detection, leveling with 3Dtouch or other sensors.Features:Compact size: 101.5mm x 72mm. Compatible with the Creatlity Ender 3 motherboard sizeFully integrated al..
40.00€ 34.99€
Ex Tax:28.92€
-48 %
Out of Stock
Stock: Out of Stock
Model: 24V 50W Heater
Voltage: 24V Power: 50WHeating head size: 6x20mmHeating head material: 304 stainless steelLine length: 1mLine thick: 0.5 mm² (the cross section of the copper wire inside the heater)Heating temperature: up to 350ºCImprovements:It can bear higher temperature rather than the original ordinary 0.3m..
4.24€ 2.20€
Ex Tax:1.82€
-40 %
Stock: In Stock
Model: IR-Module
Leveling sensor for 3D printers:It works by infrared, the sensor emits IR light and this bounces in the base of impression being identified by the sensor.Unlike resistive or capacitive sensors this sensor measures the separation distance on the upper surface of the hot bed, it does not need to be of..
35.00€ 20.99€
Ex Tax:17.35€
-48 %
Stock: In Stock
Model: LV8729
The LV8729 controller is a stepper motor driver. With a resolution of up to 1/128 steps it is very quiet and thermally efficient. With the 8-bit electronics you can reach 1/64, to use the full resolution we recommend 32-bit electronics.Heatsink included with thermal tape1 Piece ..
13.50€ 6.99€
Ex Tax:5.78€
Stock: In Stock
Model: Magnet-cut
It can be glued on a hot bed, such as the Mk3, and on this magnet can be placed the different magnetic sheets that exist on the market, such as those coated with PEI powder.They are made of a material that can be easily worked, perforated or cut with scissors and cutter to adapt to the screws of any..
7.99€
Ex Tax:6.60€
New
-22 %
Stock: In Stock
Model: Camacaliente-fysetc-220x200
Features:Rated voltage: 24VIncludes strong neodymium magnets that do not lose properties up to 140ºC4 fixing holes for countersunk screwsPre-welded power cablesThermistor included with connectorFast and uniform heatingIt may present some superficial scratches as it has been manipulated for the welds..
45.00€ 34.99€
Ex Tax:28.92€
Hot Sales
-84 %
Out of Stock
Stock: Out of Stock
Model: Final de Carrera 01
Mechanical EndStop with cable and 3-pin connector
1 Piece
..
2.99€ 0.49€
Ex Tax:0.41€
-65 %
Out of Stock
Stock: Out of Stock
Model: FC Con Rueda 1m de cable
Limit switch with wheel, 1 meter cable and 3-pin connector
1 Piece
..
4.00€ 1.39€
Ex Tax:1.15€
-28 %
Out of Stock
Stock: Out of Stock
Model: MegaCompatible
The Arduino Mega 2560 is a microcontroller board based on the ATmega2560 .It has 54 digital input/output pins (of which 15 can be used as PWM outputs), 16 analog inputs, 4 UARTs (hardware serial ports), a 16 MHz crystal oscillator, a USB connection, a power jack, an ICSP header, and a rese..
17.99€ 12.95€
Ex Tax:10.70€