-36 %
Discontinued
Stock: Discontinued
Model: SKR 1.3
3D printer board compatible with 12 and 24v, uses the powerful ARM cortex-M3 CPU 32-bit processor, and is compatible with Marlin 2.0 onwards.Compatible with virtually all controllers, which exist to date, as it can be configured with STEP/DIR, SPI or UAR controllers.Characteristics:Processor: ARM co..
39.00€ 24.99€
Ex Tax:20.65€
New
-27 %
Stock: In Stock
Model: SKR 1.4
The SKR V 1.4 plate is the successor to the popular SKR 1.3, it incorporates all the features of its previous model improving key points such asSupport for up to 4 fans (1 of them adjustable)Direct wifi compatibility.Closed-loop motor compatibility.Double connection for Z-axis motors.Support for RGB..
39.00€ 28.50€
Ex Tax:23.55€
-12 %
Out of Stock
Stock: Out of Stock
Model: Smart Filament Sensor Break Detection Module
This filament sensor not only detects when the filament runs out, nut also it is able to detect a when the filament stops moving through a jam in the extruder.Works with Marlin 2+It is compatible with screens 2004, 12864, TFT24 (12864 mode), TFT35_V3.0 (12864 mode).1 unit..
30.00€ 26.50€
Ex Tax:21.90€
-36 %
5 - 10 Days
Stock: 5 - 10 Days
Model: interruptor3pines
Power socket with switch. You can directly connect the power cable (IEC 60320 C13) without the need of welding, with the convenience of being able to connect and disconnect it at any time to facilitate transport, for example. To make the connection of the switch, it is not necessary to use welds if ..
3.03€ 1.95€
Ex Tax:1.61€
-27 %
5 - 10 Days
Stock: 5 - 10 Days
Model: Terminal FDD2-187
Terminal FDD2-187 for cable for crumping.For 1.5 to 2.5 mm² wires.With protective cover.Minimum order: 10 unitsPrice for 1 unit..
0.25€ 0.18€
Ex Tax:0.15€
-43 %
Out of Stock
Stock: Out of Stock
Model: TFT24-V1.1
Very versatile graphic display, as it can be connected in two ways at the same time:It can be connected as an external screen, using the pins TX and RX (black cable) so that you have the touch menu. This connection can be used to decrease the load on the processor.You can connect the two flat cables..
35.00€ 19.99€
Ex Tax:16.52€
-18 %
Out of Stock
Stock: Out of Stock
Model: TFT35-V3.0
Very versatile graphic display, as it can be connected in two ways at the same time:It can be connected as an external screen, using the pins TX and RX (black cable) so that you have the touch menu. This connection can be used to decrease the load on the processor.You can connect the two flat cables..
50.00€ 40.99€
Ex Tax:33.88€
New
-7 %
Stock: In Stock
Model: TFT81050
Current Version: 1.05 inch TFT81050 touch smart screen. Compatible with Marlin 2.0.Compatible with Luzbot CLCD S6 3D printer parts.Characteristics:Based on the FT810 FTDI / BridgetekEVE ChipCompatible with Luzbot CLCD!Marlin 2.0 compatibleIntegrated SD card socket (compatible with vertical SD module..
60.00€ 55.75€
Ex Tax:46.07€
-73 %
Out of Stock
Stock: Out of Stock
Model: Termistor100K ohm NTC 3950-PT100-3mm
Thermistor ideal for the Hotend. 100K ohm NTC 3950 1m wire with dupont connectorDurable 304 stainless steel capsuleDiameter 3mmDoes not need additional electronics (unlike a thermocouple)Greater precision than the normal thermistor.Maximum temperature 350ºC1 Piece..
5.00€ 1.35€
Ex Tax:1.12€
Hot Sales
Only a few units in stock
-78 %
Stock: In Stock
Model: Termistor100K ohm NTC 3950
Thermistor ideal for the Heated Bed or Hotend. 100K ohm NTC 3950 1m wire with dupont connector1 Piece..
3.20€ 0.69€
Ex Tax:0.57€
-7 %
Stock: In Stock
Model: TMC2130-SPI
Version V3.0Super silent drivers from Trinamic brand.Version for SPI, is designed for advanced users who know the Marlin firmware and want to test the new features.The special pins have output on the bottom and top, so you can configure the SPI using external wiring, or with the new plates as the Ra..
9.40€ 8.75€
Ex Tax:7.23€
New
-20 %
Stock: In Stock
Model: TMC2130-SPI-Fysetc
Version V1.2 FysetcSuper silent drivers from Trinamic brand.Version for SPI, is designed for advanced users who know the Marlin firmware and want to test the new features.The special pins have output at the bottom, so the SPI can be configured using the internal wiring on boards such as the SKR 1.4 ..
9.40€ 7.50€
Ex Tax:6.20€